17,473 Like 3,040 Dislike
Cleaning a really dirty bmw that I bought cheap cheap of a friend who recently took it in px against another car. Hope you enjoy the video 😊 Music in no particular order by... Broken Elegance - Unhappy ZAYFALL - still back Chris Henry - Peak TFLM - Wishing you Ikson - new day Bensound - creative minds.
I got this mitsubishi in to valet after the new owner had purchased it to tow a trailer with, it was previously a builders truck and it shows! In the video it is cleaned to a good usable standard. It'll never be a show winner, and there was a realistic budget set just to get the truck clean. Hope you enjoy the video! Check out this video too.. https://youtu.be/a5DDqr0gukY music courtesy of.. Imaginary by Broken Elegance & Nomyn https://soundcloud.com/brokenelegance Creative Commons — Attribution 3.0 Unported— CC BY 3.0 http://creativecommons.org/licenses/b... Music promoted by Audio Library https://youtu.be/CMLnB526kkY We Are One by Vexento https://www.youtube.com/user/Vexento https://soundcloud.com/vexento Music promoted by Audio Library https://youtu.be/Ssvu2yncgWU Road Trip by Joakim Karud https://soundcloud.com/joakimkarud Music promoted by Audio Library https://youtu.be/vpssnpH_H4c Lost Within by A Himitsu https://soundcloud.com/a-himitsu Creative Commons — Attribution 3.0 Unported— CC BY 3.0 http://creativecommons.org/licenses/b... Music promoted by Audio Library https://youtu.be/DHNZeIy4kjs
Another week another severely neglected and rusty item goes onto the bench to get brought back to life! This week the item in question is a SEVERELY NEGLECTED MOTORCYCLE WHEEL that has certainly seen better days. Now before i begin the description i would like to take a moment to say this wheel is NOT going back on the road so please dont flood the comments section saying that i never used new bolts for the brake disc or torqued them down to the required lbs/ft or removed or replaced the bearings etc etc you get the idea. Also let me know what you think of the editing on this one, ive tried to cut it down and speed up the more boring sections to keep the overall time down as i know lots of you guys wont have a good hour and a half spare to watch a wheel being refurbished at normal speeds. If you think its to fast and choppy please let me know and ill revert to the longer and less choppy cuts. Anyway..... First thing is first the obligatory before close up and as you can see from it the wheel is in a very poor condition, sitting in a muddy corner for years and spiders living in the centre hub have certainly made a monster out of this once lovely wheel! The first job on the list was to get in on the tyre machine and get the beads broken to allow the shoe of the machine to lift the tyre off, then while it was clamped in the machine i thought this is a perfect time to remove the brake disc bolts while its clamped down to a solid surface as these bolts can be a right pig to remove if they have been over tightened and flooded with thread locking compound. To my surprise they broke loose fairly easily. Next on the list was getting it on the workbench and getting it torn down completely first out were the cushions for the drive sprocket (actually in very good condition for the age and the weathering they have been through!) then off the the old valve neck and wheel weights. The brake disc and bolts were then put in a DEOX C bath while i worked on the rest of the rim. To clean the surface grime and muck from the rim CONCEPT CHEMICALS MASTER CLEANER was used at a low dilution ration then agitated aggressively with a VIKAN brush after soaking for a few minutes it was time to pressure wash it clean and get a look at what i actually had to play with. It wasn't too bad but definitely did require a lot of attention to get it looking its best again! Out came the PAINT PANTHER for the next stage which was to remove the old nasty paint to reveal the lovely diamond cut alloy edges and shot peened hub and spokes, Not being a fan of polished metal it was at this point i decided on an all paint finish but at this stage i wasn't sure about colour. After a bit of wire brushing with the dremel and a good hand sanding it was time to get it masked up and into primer. First came 2 light coats of U-POL ETCH PRIMER to give the high build primer a solid base to grip onto.The HIGH SOLID HIGH BUILD PRIMER went on in three coats with sufficient time left between coats for maximum build. After that was dry a bit of wet sanding was required mostly in the centre of the wheel to eradicate the shot peening marks so that the rim would have a uniform gloss finish when done. PREPARATION IS THE KEY TO A FANTASTIC FINISH! For doing the base coat and lacquering it is necessary to make some sort of rig so that you can get at both sides of the wheel instantly, if you only try to paint one side of a wheel and then flip it over to get the other side all you end up with is one side that looks passable and the other that looks shockingly bad! Before i could begin painting it was necessary to do a few touch ups with a little aerosol primer where i had to sand quite far down to get a uniform smooth finish after that was done and dried it was time to spray my colour choice REPSOL ORANGE After the base and clear was done i took the mad notion to run a single pin stripe round and im glad i did i really like the way the silver pops out from the REPSOL ORANGE. Then it was simply a case of cleaning up a few bolts and re-assembling the wheel. If you like what you see and have any ideas for the channel please let me know in the comment section. And as usual if you liked the video please like subscribe and share this video and help the channel grow. Really Random Channel.
Support the channel by buying my MERCH: https://teespring.com/stores/carsoverdose ALSO USE CODE "OVERDOSER" TO GET 10% OFF YOUR PURCHASE Hey OVERDOSERS🔥🔥🔥 it's me back with another Video "Satisfying Car Guys Moments | Only Car Guys Will Understand this PART 5". I hope you like it. If you have any video ideas please mention them in the comments and i'll be happy to respond or do that video idea. And remember. Always stay litt 🔥🔥😜🔥 Also please follow me on Twitter: https://twitter.com/Cars_Overdose And Instagram: https://www.instagram.com/carsoverdosetv/ Thanks for watching. Credits are edited in the video and the videos on this compilation are all from INSTAGRAM. "Copyright Disclaimer Under Section 107 of the Copyright Act 1976, allowance is made for "fair use" for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favor of fair use." I do NOT own the video materials and all credits belong to respectful owners. In case of copyright issues, please contact me immediately for further credits or clip delete.
Lavage auto avec détergent Fraber superlava teli
Call now @ 03088400814 or visit pkwash.com for bookings.Try now and get your car completely refreshed with our doorstep service available all over Pakistan.